行業資訊

瀝青冷補料使用方法介紹

來源：http://www.apdetong.cn/ 日期：2023-05-12

今天根據濟南瀝青料廠家實際調研與市政、高速養護等施工單位的探討，總結出的瀝青冷補料使用方法，希望可以給您帶來一些幫助。

Today, based on the actual research of asphalt manufacturers in Jinan and discussions with construction units such as municipal and high-speed maintenance, the usage methods of asphalt cold patching materials have been summarized, hoping to provide you with some help.

1.使用瀝青冷補料時對坑槽的處理，先要確定坑槽開挖位置，四周銑刨（根據路面厚度，深度一般不低于3厘米）或切縫后，將待修補的坑槽內及四周的碎石、廢渣清理干凈，坑槽內不得存有污水，泥漿，冰塊等雜物，被修補的坑槽應有整齊的切邊，廢渣的清除要見到固體的堅固面為止。

1. When using asphalt cold patching materials, the treatment of pits and grooves should first determine the excavation position of the pits and grooves. After milling around (according to the thickness of the road surface, the depth is generally not less than 3 centimeters) or cutting the joints, the crushed stones and waste residue in and around the pits and grooves to be repaired should be cleaned up. There should be no sewage, mud, ice blocks or other debris in the pits and grooves to be repaired, and the edges of the repaired pits and grooves should be neatly cut. The removal of waste residue should be done until a solid solid surface is visible.

2.使用瀝青冷補料填補坑槽時建議在清理好的坑槽四周及底部刷涂粘層油，尤其是坑槽四周要涂刷均勻（根據實際施工經驗粘層油對于新老路面結合有很好的輔助作用）。

2. When using asphalt cold patching material to fill the pit, it is recommended to apply adhesive layer oil around and at the bottom of the cleaned pit, especially evenly around the pit (based on actual construction experience, adhesive layer oil has a good auxiliary effect on the combination of new and old road surfaces).
濟南瀝青料

3.把足夠的瀝青冷補料填進坑槽內，瀝青冷補料應首先攤?cè)氩郾谒闹?，由邊向中攤鋪。直到填料高出地?.5厘米左右，填滿后坑槽中央處應稍高于四周路面并呈弧形。如路面坑槽破損深度在5厘米以上時，填補工作應以每3厘米為一層，分層填補、逐層壓實。

3. Fill sufficient asphalt cold patching material into the pit and groove. The asphalt cold patching material should be first spread around the groove wall, from edge to center. Until the filling material is about 1.5 centimeters above the ground, the center of the pit should be slightly higher than the surrounding road surface and curved after filling. If the depth of damage to road grooves is more than 5 centimeters, the filling work should be done in layers of every 3 centimeters, and compacted layer by layer.

4.在瀝青冷補料壓實完成后根據需要可在表面均勻撒上一層石粉或細沙，并用清掃工具來回清掃，以便細沙填滿表面空隙。之后就可以開放交通了。

4. After the compaction of the asphalt cold patching material is completed, a layer of stone powder or fine sand can be evenly spread on the surface as needed, and a cleaning tool can be used to sweep back and forth to fill the surface gaps with fine sand. After that, traffic can be opened up.

以上就是瀝青冷補料的使用方法介紹，希望可以給您帶來幫助。更多相關事項就來我們網站http://www.apdetong.cn進行咨詢吧！

The above is an introduction to the use of asphalt cold patching materials, hoping to be helpful to you. For more related matters, come to our website http://www.apdetong.cn Let's consult!

上一條：路面機械設備的配件磨損原因

下一條：挖掘機的基本操作有哪些？